9.Locked (alarm or jog)
- kulfon250wr
- Messages : 32
- Enregistré le : 04 mai 2023 01:18
- Localisation : Poland
- Contact :
9.Locked (alarm or jog)
1.I get this error every time I run it. Unlocking it requires moving the axis forward/back three times and then the padlock unlocks it. What could it be? I didn't have this in firmware 1, now in 2.1 every time.
2. In firmware 1, after starting the engines were not blocked, the head could be moved. Unfortunately, in 2.1 it is not possible to do it manually, is it on purpose or is something wrong with me?
2. In firmware 1, after starting the engines were not blocked, the head could be moved. Unfortunately, in 2.1 it is not possible to do it manually, is it on purpose or is something wrong with me?
Vous n’avez pas les permissions nécessaires pour voir les fichiers joints à ce message.
- rominetb44
- Messages : 680
- Enregistré le : 10 déc. 2020 13:06
Re: 9.Locked (alarm or jog)
Hi kulfon250wr,
The message "Cmd JOG:missing OK" means there is no answer received from GRBL within 500msec for Jog command (moving with nunchuck or with arrow in Auto mode).
This is probably a consequence of an error in GRBL.
Could you give us the answer to the command "?" when GRBL is Locked ?
Thanks
The message "Cmd JOG:missing OK" means there is no answer received from GRBL within 500msec for Jog command (moving with nunchuck or with arrow in Auto mode).
This is probably a consequence of an error in GRBL.
Could you give us the answer to the command "?" when GRBL is Locked ?
Thanks
- kulfon250wr
- Messages : 32
- Enregistré le : 04 mai 2023 01:18
- Localisation : Poland
- Contact :
Re: 9.Locked (alarm or jog)
The nunchuk is connected and after manual unlocking it works normally.
Clean software 2.1 is installed, without any changes.
I don't really know how to check the "?" command. Can you explain what to do, I'm not an IT specialist.
Clean software 2.1 is installed, without any changes.
I don't really know how to check the "?" command. Can you explain what to do, I'm not an IT specialist.
- rominetb44
- Messages : 680
- Enregistré le : 10 déc. 2020 13:06
Re: 9.Locked (alarm or jog)
Hi kulfon250wr,
Could you confirm that u are using GRBL board V1.0/1.5 and not GRBL board V2.0 ?
Did you make any change in GRBL configuration ?
Did you use a software to connect a PC to GRBL lately ?
See u
Could you confirm that u are using GRBL board V1.0/1.5 and not GRBL board V2.0 ?
This is a parameter of GRBL that you can set with the $1=255 command.kulfon250wr a écrit : ↑01 févr. 2024 22:49 2. In firmware 1, after starting the engines were not blocked, the head could be moved. Unfortunately, in 2.1 it is not possible to do it manually, is it on purpose or is something wrong with me?
Did you make any change in GRBL configuration ?
Did you use a software to connect a PC to GRBL lately ?
See u
- kulfon250wr
- Messages : 32
- Enregistré le : 04 mai 2023 01:18
- Localisation : Poland
- Contact :
Re: 9.Locked (alarm or jog)
Hey,
Yes I used GRBL board V2.0.
Did you make any change in GRBL configuration ?
No
Did you use a software to connect a PC to GRBL lately ?
Yes, but nothing change
Yes I used GRBL board V2.0.
Did you make any change in GRBL configuration ?
No
Did you use a software to connect a PC to GRBL lately ?
Yes, but nothing change
- kulfon250wr
- Messages : 32
- Enregistré le : 04 mai 2023 01:18
- Localisation : Poland
- Contact :
Re: 9.Locked (alarm or jog)
Ok, sorry, I mixed up threads, this is thread 1/1.5, can it be moved?
- rominetb44
- Messages : 680
- Enregistré le : 10 déc. 2020 13:06
Re: 9.Locked (alarm or jog)
Hi kulfon250wr,
In WebUI you can send the command "?" in the window Commands and post the answer.
You can so check the value of $1 by sending "$1" command. Otherwise you can send all this commands with a software as LightBurn, LaserGRBL, Estlcam, ...
Which software are u using ?
See U
So you can check the status of GRBL with WebUI.
In WebUI you can send the command "?" in the window Commands and post the answer.
You can so check the value of $1 by sending "$1" command. Otherwise you can send all this commands with a software as LightBurn, LaserGRBL, Estlcam, ...
Be careful, you have to unplug the screen board when connecting a PC to the ESP of the GRBL board (same serial port).kulfon250wr a écrit : ↑02 févr. 2024 20:50 Did you make any change in GRBL configuration ?
No
Did you use a software to connect a PC to GRBL lately ?
Yes, but nothing change
Which software are u using ?
See U
Vous n’avez pas les permissions nécessaires pour voir les fichiers joints à ce message.
- kulfon250wr
- Messages : 32
- Enregistré le : 04 mai 2023 01:18
- Localisation : Poland
- Contact :
Re: 9.Locked (alarm or jog)
I had $1=255, I set $1=0 and now after turning on the stepp engines are turned off ![Sourire :)](./images/smilies/icon_e_smile.gif)
![Sourire :)](./images/smilies/icon_e_smile.gif)
- rominetb44
- Messages : 680
- Enregistré le : 10 déc. 2020 13:06
Re: 9.Locked (alarm or jog)
Hi kulfon250wr,kulfon250wr a écrit : ↑18 févr. 2024 14:50 I had $1=255, I set $1=0 and now after turning on the stepp engines are turned off![]()
Sorry, I made a mistake, you'are right for unlocking the motor the value of $1 shouldn't be 255.
Good job !
Do you still get an alarm ?
See you
- kulfon250wr
- Messages : 32
- Enregistré le : 04 mai 2023 01:18
- Localisation : Poland
- Contact :
Re: 9.Locked (alarm or jog)
The alarms are still there as in the photos and I have to manually unclick them