Firmware 2.0.x vs 2.1.g

Avatar du membre
kulfon250wr
Messages : 32
Enregistré le : 04 mai 2023 01:18
Localisation : Poland
Contact :

Firmware 2.0.x vs 2.1.g

Message par kulfon250wr »

Hello
I have firmware version 2.0.x is it worth upgrading to version 2.1.g??
In my machine, it happens that when cutting for a long time (a lot of elements), the software hangs, the spindle stops or goes in the wrong direction. Can an upgrade help?
B/r
Maciej
Avatar du membre
HTheatre
Messages : 5914
Enregistré le : 31 mars 2019 08:21
Localisation : Rivesaltes

Re: Firmware 2.0.x vs 2.1.g

Message par HTheatre »

Hi kulfon250wr,

Actually, we are at the version 2.1.jOTA (26 april 2023) for the TFT firmware. I invite you to update anyway.
The update will probably not solve your issue of motors going in the wrong way. For that, I suggest to check the DIR- wire connections of the concerned drivers. Check their connections between the drivers and the Grbl board. DIR- signal controls the way of rotation of the motors.

See ya,
Avatar du membre
kulfon250wr
Messages : 32
Enregistré le : 04 mai 2023 01:18
Localisation : Poland
Contact :

Re: Firmware 2.0.x vs 2.1.g

Message par kulfon250wr »

Hello
Thx for answer, but
The problem is that the plotter cuts well for 40 minutes and suddenly goes stupid, it's not a connection problem, it's something in electronics or software that causes it
Avatar du membre
kulfon250wr
Messages : 32
Enregistré le : 04 mai 2023 01:18
Localisation : Poland
Contact :

Re: Firmware 2.0.x vs 2.1.g

Message par kulfon250wr »

Problem with Firmware in Arduino..
Vous n’avez pas les permissions nécessaires pour voir les fichiers joints à ce message.
Avatar du membre
rominetb44
Messages : 650
Enregistré le : 10 déc. 2020 13:06

Re: Firmware 2.0.x vs 2.1.g

Message par rominetb44 »

Hi,

Which OS are you using ?
Which version of Arduino are U using ?
What is the size of your TFT ?

Regards,
Avatar du membre
kulfon250wr
Messages : 32
Enregistré le : 04 mai 2023 01:18
Localisation : Poland
Contact :

Re: Firmware 2.0.x vs 2.1.g

Message par kulfon250wr »

Arduino 2.1.0
MacOs Ventura 13.4
TFT 3,2"
Board 1.0-1.5
Avatar du membre
rominetb44
Messages : 650
Enregistré le : 10 déc. 2020 13:06

Re: Firmware 2.0.x vs 2.1.g

Message par rominetb44 »

Hi,

I think it is an issue of Arduino 2.1.0 or MacOs (I'll try tomorrow).
You should better use Arduino 1.8.19.
However, I fix the issue changing the name of the files.
You could try it : https://github.com/rominetb44/grbl_cont ... master.zip

Let's me know if it's ok.

See u
Avatar du membre
kulfon250wr
Messages : 32
Enregistré le : 04 mai 2023 01:18
Localisation : Poland
Contact :

Re: Firmware 2.0.x vs 2.1.g

Message par kulfon250wr »

The same situation, tomorrow i try Arduino 1.8.19
Vous n’avez pas les permissions nécessaires pour voir les fichiers joints à ce message.
Avatar du membre
rominetb44
Messages : 650
Enregistré le : 10 déc. 2020 13:06

Re: Firmware 2.0.x vs 2.1.g

Message par rominetb44 »

I think it is due to bracket....
Let me know with Arduino 1.8.19. Otherwise, I will change the name of this files.

see U
Avatar du membre
rominetb44
Messages : 650
Enregistré le : 10 déc. 2020 13:06

Re: Firmware 2.0.x vs 2.1.g

Message par rominetb44 »

rominetb44 a écrit : 04 mai 2023 21:35 I think it is due to bracket....
Let me know with Arduino 1.8.19. Otherwise, I will change the name of this files.

see U
In fact, these files are no longer used...
You can dowload again the firmware :
https://github.com/rominetb44/grbl_cont ... master.zip

See U.
Répondre