Its done!!
Right now everything works properly!
Made new short and shielded wires between STM32 and ESP32 and a accurate grounding and it works!
Thanks Romain!! - and as well to all other for support!
Now I can start to calibrate
20 résultats trouvés
- 21 juin 2021 23:11
- Forum : GRBL32bits V1.0/1.5
- Sujet : Machine stops randomly (fixed)
- Réponses : 9
- Vues : 3828
- 20 juin 2021 10:33
- Forum : GRBL32bits V1.0/1.5
- Sujet : Machine stops randomly (fixed)
- Réponses : 9
- Vues : 3828
Re: Machine stops randomly
Okey,
If everything is falling apart, I can still make an update.
Beneath that - last week I was shortly before at the point to make an order
Thanks for your great support!
I'll report if it works.
see ya
If everything is falling apart, I can still make an update.
Beneath that - last week I was shortly before at the point to make an order
Thanks for your great support!
I'll report if it works.
see ya
- 19 juin 2021 10:52
- Forum : GRBL32bits V1.0/1.5
- Sujet : Machine stops randomly (fixed)
- Réponses : 9
- Vues : 3828
Re: Machine stops randomly
Hi Romain, thanks for your answer. I used two separate shielded cables for TX and RX and a unshielded double twisted cable for power and ground to the board. One of them is a bit long - I'll cut it today and try again. Puuh, I took hours of solving this problem, first with different files and parame...
- 18 juin 2021 09:42
- Forum : GRBL32bits V1.0/1.5
- Sujet : Machine stops randomly (fixed)
- Réponses : 9
- Vues : 3828
Re: Machine stops randomly
Thx for the tip,
tried another one, but it's unfortunately the same - stops at 4%
tried another one, but it's unfortunately the same - stops at 4%
- 16 juin 2021 10:37
- Forum : GRBL32bits V1.0/1.5
- Sujet : (Fixed!) Gcode suspended for more than 2 min error
- Réponses : 3
- Vues : 2946
Re: (Fixed!) Gcode suspended for more than 2 min error
Thanks for sharing your experience. I think that some members also had similar issues even when the ESP32 was not connected to a PC. Did you ever try to use another power supply (not the 24V) for the ESP32 and STM32. Perhaps it could also help. Can I use a 36V power-supply without any limitations r...
- 16 juin 2021 10:24
- Forum : GRBL32bits V1.0/1.5
- Sujet : Machine stops randomly (fixed)
- Réponses : 9
- Vues : 3828
Re: Machine stops randomly - Gcode suspended for more than 2 minutes
Seems the same problem as in:
viewtopic.php?t=7315
But unplugging the usb-cable helps not!!
Anybody any idea?
(1000rpm is not real - spindle is not connected!)
viewtopic.php?t=7315
But unplugging the usb-cable helps not!!
Anybody any idea?
(1000rpm is not real - spindle is not connected!)
- 12 juin 2021 14:28
- Forum : GRBL32bits V1.0/1.5
- Sujet : Machine stops randomly (fixed)
- Réponses : 9
- Vues : 3828
Machine stops randomly (fixed)
Hi, having my next problem and need some help again, please. Machine is running, everything seems okey, (except the z-probe, but it can't depend on this) and testing several jobs I have always the same problem: machine stops randomly! And its not reproducible. The same job sometimes stops at 3%, 12%...
- 07 juin 2021 23:57
- Forum : GRBL32bits V1.0/1.5
- Sujet : GRBL Settings
- Réponses : 5
- Vues : 2135
Re: GRBL Settings
Problem solved!
I think it was a missing contact on the z-probe.
Now it works!
Thanks!
I think it was a missing contact on the z-probe.
Now it works!
Thanks!
- 07 juin 2021 23:27
- Forum : GRBL32bits V1.0/1.5
- Sujet : GRBL Settings
- Réponses : 5
- Vues : 2135
Re: GRBL Settings
Hi, first, I increased $110 and $111 - it works. Machine is fast enough. Thanks for the tip! Homing sequence is also fine. Machine stops ca. 3mm before the switches after pushing them in the front left corner. Okey, but now I have the next problem with the z-probe. After touching the probe, machine ...
- 07 juin 2021 12:07
- Forum : GRBL32bits V1.0/1.5
- Sujet : GRBL Settings
- Réponses : 5
- Vues : 2135
Re: GRBL Settings
Hi, okey, thanks for help. I'll try the higher values. Regarding the homing. I do not know the setup sequence of homing?! Just push the button "Home" and the machine make the rest for itself? I've read the instructions for $23 "homing dir invert" and it tells me machine is moving...