10 résultats trouvés
- 22 févr. 2021 19:47
- Forum : Montage R-CNC
- Sujet : Laser problems
- Réponses : 8
- Vues : 5146
Re: Laser problems
Thanks. That worked.
- 22 févr. 2021 10:27
- Forum : Montage R-CNC
- Sujet : Laser problems
- Réponses : 8
- Vues : 5146
Re: Laser problems
thanks i will give it a go
- 22 févr. 2021 09:27
- Forum : Montage R-CNC
- Sujet : Laser problems
- Réponses : 8
- Vues : 5146
Re: Laser problems
Wow this is difficult I followed the instructions. Using Attolic True Studio. I open config.h and remove the # from the #define INVERT_SPINDLE_PWM command I then rebuild the project and it generates 2 errors expected '=', ',', ';', 'asm' or '__attribute__' before 'uint8_t' in nuts_bolts.h and unknow...
- 21 févr. 2021 15:09
- Forum : Montage R-CNC
- Sujet : Laser problems
- Réponses : 8
- Vues : 5146
Re: Laser problems
Hello again.
I've looked at the GRBL using Antonio and am completely confused.
Can you give me an idea as to what I should be looking for.
Where I should find it and
What I should change it to.
Any help is appreciated. I think my brain may be too old for this steep learning curve
Thanks
I've looked at the GRBL using Antonio and am completely confused.
Can you give me an idea as to what I should be looking for.
Where I should find it and
What I should change it to.
Any help is appreciated. I think my brain may be too old for this steep learning curve
Thanks
- 20 févr. 2021 18:31
- Forum : Montage R-CNC
- Sujet : Laser problems
- Réponses : 8
- Vues : 5146
Re: Laser problems
Thanks. I will have a look.. im not sure how to invert the PWM . Hopefully it may become clear when I take a look tomorrow
Thanks
Thanks
- 20 févr. 2021 14:24
- Forum : Montage R-CNC
- Sujet : Laser problems
- Réponses : 8
- Vues : 5146
Laser problems
Hello. I don't know if I'm in the correct place on this forum but I need help with the laser on my RCNC32 I've mounted at 15 watt laser and connected it to the board. Following the instructions on the firmware section. The laser works but in the negative.. When I switch on it immediately lights up a...
- 11 févr. 2021 09:46
- Forum : Montage R-CNC
- Sujet : Help with firmware
- Réponses : 5
- Vues : 3259
Re: Help with firmware
Yes it was a dry joint on the board
Thanks for solving my problem
Thanks for solving my problem
- 09 févr. 2021 20:19
- Forum : Montage R-CNC
- Sujet : Help with firmware
- Réponses : 5
- Vues : 3259
Re: Help with firmware
Thank you. I will try all those things
Your help is appreciated
Your help is appreciated
- 09 févr. 2021 17:06
- Forum : Montage R-CNC
- Sujet : Help with firmware
- Réponses : 5
- Vues : 3259
Re: Help with firmware
Thank you . Well I checked that and sure enough. There was a connection issue. Right pins but a bad connection. I now get the idle message and have better speeds. Also the numchuck now works. However I still have these problems No Z+ rotation. I have swapped the steppers around and eliminated any st...
- 09 févr. 2021 13:41
- Forum : Montage R-CNC
- Sujet : Help with firmware
- Réponses : 5
- Vues : 3259
Help with firmware
Hello. I hope someone can help me. I've made 3 RCNC 32 for use in our lock down SHAREDWORKS community. Mechanically all looks good but we can't get the firmware to work properly. On power up we get buttons on the touch screen which seem to drive the steppers but very slowly X and Y axis steppers rot...