18 résultats trouvés
- 17 juil. 2021 00:12
- Forum : GRBL32bits V1.0/1.5
- Sujet : Candle issue
- Réponses : 15
- Vues : 5668
Re: Candle issue
First test of one little Project for my new datalogger pcb went without any incident and/or problem. So it's looking really good, since the hole pcb took more than 2 hours to make. It seems changing the baud rate to 57600 was, at least for me, the solution for now... I really hope :lol: So for now, ...
- 16 juil. 2021 01:28
- Forum : GRBL32bits V1.0/1.5
- Sujet : Candle issue
- Réponses : 15
- Vues : 5668
Re: Candle issue
It seems so easy :arrow: I tried to flash both STM32 and ESP32 with the adapted fw with a baud rate of 57600 and 38400, for which I changed the baud rates implemented in the - STM32 GRBL fw / config.h 89 // Serial baud rate 90 #define BAUD_RATE 57600 - ESP32 TFT fw / grbl_controller_esp32 192 Serial...
- 15 juil. 2021 20:54
- Forum : GRBL32bits V1.0/1.5
- Sujet : Candle issue
- Réponses : 15
- Vues : 5668
Re: Candle issue
Hi htheatr, thanks for the advice, I will follow up when I have made the changes, might there be any experience whether which baudrate might work properly? What might be the downside to change the baudrate to a lower value, anything which I need take into account when sending cnc commands directly v...
- 14 juil. 2021 21:56
- Forum : GRBL32bits V1.0/1.5
- Sujet : Candle issue
- Réponses : 15
- Vues : 5668
Re: Candle issue
Hi guys, since my workshop is coming along I changed the position of the CNC and you might laugh but my issues started again... :roll: I forgot to answer to the last comment... thanks for the hint, since I definetly need a height map implemented for the pcb stuff... how can I do that, when working w...
- 05 mai 2021 00:30
- Forum : GRBL32bits V1.0/1.5
- Sujet : Candle issue
- Réponses : 15
- Vues : 5668
Re: Candle issue
Busy day ;-) but at least I can go to sleep with a good feeling... I haven't seen you reply before but... - I changed the USB cable which at first which looked like it helped, but after some test runs without problems I hade the same issue - then I deinstalled arduino IDE completly including all lib...
- 04 mai 2021 13:30
- Forum : GRBL32bits V1.0/1.5
- Sujet : Candle issue
- Réponses : 15
- Vues : 5668
Re: Candle issue
I followed the online tutorial - updated arduino IDE to 1.8.13 - installed the board from the provided link - installed SDFAT in version 2.0.6 - downloaded the firmware via link from the tutorial ("Firware vers. 2.0.v (3 may 2021)") - set in config.h - #define WIFI to NO_WIFI - commented #...
- 04 mai 2021 11:20
- Forum : GRBL32bits V1.0/1.5
- Sujet : Candle issue
- Réponses : 15
- Vues : 5668
Re: Candle issue
Hi, it seems I'm running out of luck... I tried to flash the esp32 anew but I'm running into more problems even there... if I try to I get following error message "cannot declare variable 'telnetServer' to be of abstract type 'WifiServer'" - full message is in the attached txt file :o - I ...
- 03 mai 2021 22:19
- Forum : GRBL32bits V1.0/1.5
- Sujet : Candle issue
- Réponses : 15
- Vues : 5668
Candle issue
Hi, long time no see - i moved therefore my rs was quite a time out of work... now I wanted to get it back on track and start some pcb work but run into an issue. I wanted to use candle for the pcb milling since there is a heightmap function which is quite helpfull in this little dimensions. Everyth...
- 14 nov. 2019 00:21
- Forum : GRBL32bits V1.0/1.5
- Sujet : Laser engraving module
- Réponses : 16
- Vues : 9740
- 13 nov. 2019 16:42
- Forum : GRBL32bits V1.0/1.5
- Sujet : Fusion 360 postprocessor for grbl 32 version?
- Réponses : 4
- Vues : 3704
Re: Fusion 360 postprocessor for grbl 32 version?
Hey guys,
would be great to hear whether or not it worked?
would be great to hear whether or not it worked?