Hello
Is this is ok?.. on picture are 3 conectors, i have only 2
16 résultats trouvés
- 14 févr. 2021 17:40
- Forum : GRBL32bits V1.0/1.5
- Sujet : Nunchuk
- Réponses : 1
- Vues : 1181
- 08 déc. 2020 16:59
- Forum : GRBL32bits V1.0/1.5
- Sujet : grbl esp32 error
- Réponses : 7
- Vues : 3071
Re: grbl esp32 error
Hello It looks like ESP32 can't connect to the COM port. How do I even know which COM port is right - via USB? And how to install the right driver for COM port. I bought a new ESP 32 but it's the same Arduino: 1.8.12 (Windows 7), Board: "ESP32 Dev Module, Disabled, Default, 240MHz (WiFi/BT), QI...
- 06 déc. 2020 20:21
- Forum : GRBL32bits V1.0/1.5
- Sujet : grbl esp32 error
- Réponses : 7
- Vues : 3071
Re: grbl esp32 error
Hello thanks.. im load proper version, but now I get this error: Arduino: 1.8.12 (Windows 7), Board: "ESP32 Dev Module, Disabled, Default, 240MHz (WiFi/BT), QIO, 80MHz, 4MB (32Mb), 921600, None" Sketch uses 890966 bytes (67%) of program storage space. Maximum is 1310720 bytes. Global varia...
- 06 déc. 2020 15:32
- Forum : GRBL32bits V1.0/1.5
- Sujet : grbl esp32 error
- Réponses : 7
- Vues : 3071
grbl esp32 error
Hello What im doing wrong... to get this erroor Arduino: 1.8.12 (Windows 7), Board: "ESP32 Dev Module, Disabled, Default 4MB with spiffs (1.2MB APP/1.5MB SPIFFS), 240MHz (WiFi/BT), QIO, 80MHz, 4MB (32Mb), 921600, None" menu_file.cpp:53:1: error: 'File' does not name a type File fileToShow ...
- 04 mars 2020 17:52
- Forum : GRBL32bits V1.0/1.5
- Sujet : rs-cnc not work
- Réponses : 3
- Vues : 2222
Re: rs-cnc not work
hi
Im upload new firmware "without" nunchuk. I run with shield on and get what is in picture.. no response from spinndle relay..
Im upload new firmware "without" nunchuk. I run with shield on and get what is in picture.. no response from spinndle relay..
- 03 mars 2020 22:06
- Forum : GRBL32bits V1.0/1.5
- Sujet : rs-cnc not work
- Réponses : 3
- Vues : 2222
rs-cnc not work
hello I put together a RS CNC. loaded the TFT firmware and the screen works OK. I also loaded the firmware on the Arduino and it went OK too. when i plug in everything as instructed it doesn't work. I have already replaced Mega2560 but it still does not work. Since I have no end switches, I installe...
- 01 sept. 2018 13:59
- Forum : R-CNC Assembly
- Sujet : R-CNC x pulley replace
- Réponses : 5
- Vues : 8046
Re: R-CNC x pulley replace
I will try, and post how work
- 31 août 2018 23:51
- Forum : R-CNC Assembly
- Sujet : R-CNC x pulley replace
- Réponses : 5
- Vues : 8046
R-CNC x pulley replace
Hello
I think that X pulleys and X motor at RS-CNC is very good solution. My question is, if possible modified "old" R-CNC with this two part.
Thanks for answer..
Best regards
Sebastjan
I think that X pulleys and X motor at RS-CNC is very good solution. My question is, if possible modified "old" R-CNC with this two part.
Thanks for answer..
Best regards
Sebastjan
- 13 avr. 2018 20:14
- Forum : R-CNC Adjustments
- Sujet : different size like draw
- Réponses : 2
- Vues : 6980
Re: different size like draw
Thanks for info... Is there any instructions for "dummies" how install repetier firmware instead mailin?
- 13 avr. 2018 00:18
- Forum : R-CNC Adjustments
- Sujet : different size like draw
- Réponses : 2
- Vues : 6980
different size like draw
Hello
Im noticed that piece are sligtly bigger then I draw. Example : 10x40 mm is milled about 10,9x 40,9mm. I also notice that small holes are square 2 mm size. I use 1 mm milling bit and corel drav to convert to DXF and thene ESTLCAM.
Thanks for some tip..
Im noticed that piece are sligtly bigger then I draw. Example : 10x40 mm is milled about 10,9x 40,9mm. I also notice that small holes are square 2 mm size. I use 1 mm milling bit and corel drav to convert to DXF and thene ESTLCAM.
Thanks for some tip..